I designed, built, and installed the controller for around $100.  Here is a brief description of how to build your own DSC.  This is by no means an exhaustive, step-by-step guide, and you will require knowledge of electrical wiring, soldering, programming, Linux, web servers, and more.

Temperature Sensors

A single strand of Cat5 cable forms a bus for a network of Dallas DS1820+ 1-wire temperature sensors (datasheet).  The Cat5 cable is run from the controller (using RJ-45 connector), past the heat exchanger (for input, output, and tank sensors) and cold water inputs, then up onto the roof and into the temperature sensor well inside the solar collector.  Temperature sensors can be added anywhere along the bus using telephone 3-Wire Butt Splice (blue) connectors.  Be sure to crimp them tightly so that all the wires make solid contact.  Using TIA/EIA-568-B wiring:

• Blue = DQ (pin 2)
• Blue/White = GND (pin 1)
• Orange = +5V (pin 3)

Solder a 6″ lead to each leg of the DS1820.  Use higher-temperature wire for the roof sensor (125 C +).  Wrap leg #2 in 1/8″ heat-shrink, then wrap the entire device (all three legs and part of the semiconductor) in 1/4″ heat-shrink.

The temperature sensor can be mounted to a conductive surface (pipe, side of a tank, etc.) using 3M Picture Hanging Strips, Exterior Mounting Tape, or plain old duct tape.  They can also be inserted into metal knitting needles and sealed with epoxy to make probes.

Controller Hardware

Using the links below, you can order all the parts you need to build your own DSC, assuming you can read a schematic and solder (some surface mount parts).  Don’t forget to add at least 2 (4 is better) Dallas 1-wire temperature sensors (DS-1820) to your parts order.

• schematic for the DSC controller (PDF)
• digikey-partslist (CSV) – includes Digikey Part Numbers required to populate the PCB.  Other Digikey parts may be required – read on for a complete list.
• printed circuit board – order from Batch PCB
• Arduino Duemilanove – purchase online from SparkFun or Adafruit

The PCB is an Arduino shield that mates with the Duemilanove.  You could also build the controller on a prototype board or using a prototype shield from SparkFun or Adafruit.  As you can see from the schematic, the circuit is not that complicated, and most parts can be swapped or omitted, except for R1 (4K7) which is a required value for the 1-Wire bus.

The PCB is my design and can be used for non-commercial purposes, with no warranty.  It’s been tested though and is the same board design I am currently using to run my solar hot water system.  BatchPCB provides low-cost, small run, well made printed circuit boards.  The link above should allow you to place your own order directly without any middlemen (ie. Me).  I’ve used BatchPCB for many projects and have always been happy with the results.

The parts list has Digkey part numbers to all the components I used to populate the PCB.  If you notice Digikey no longer stocks a part, or you’re wondering about compatibility with other part numbers, please let me know.  Digikey has a reasonable shipping and handling fee, considering that you can place an order at noon today and have the parts on your desk by noon tomorrow.

A relay runs a 120V AC Grundfos UP26-99 circulator pump, which will draw at most 2.1A.   Make sure the relay can handle the current needed to run your pump (see datasheet), and if necessary choose another relay with the same footprint.  The relay listed is rated for 12A@250VAC.

Wiring and Enclosure

Because this circuit uses 12VDC and 120V AC, ensure you mount the controller in an appropriate enclosure and take all the usual precautions when dealing with electricity.   Required parts:

• metal or plastic (easier to drill) enclosure – 4x4x6 leaves lots of room for wiring
• LED lenses (need part number)
• AC Hour Meter (optional)
• AC Toggle Switch

The controller can be wired directly, or fitted with an AC plug.  The connection between the pump and the controller can also be made using AC plugs and sockets.

Firmware

Built with the Arduino environment and the Dallas Temperature Control Library.  Download the sketch.

Logging

The system can be monitored using the USB/serial port of the Arduino.  I use a bash script running on a linux laptop that is called from a cron job to read the state and temperatures via tty and insert them into a round robin database to create useful graphs.  The bash script also outputs an XML file, which is used as the data source for the Solar Hot Water Google Gadget.  Get the gadget and view the system status here.

You can also read some details on the installation of the collectors and the building of the heat exchanger, and there are some construction photos here.